Front Emplacement of Batteries in Fork Bags: A Dual-Battery Touring Build
We share this guest post with great thanks to Crosbie Fitch, whose personal experience and expertise made it possible. Crosbie converted a 1980 Claud Butler Majestic touring bike with a CYC Photon Gen 2 and moved its two batteries into fork bags to balance a heavily loaded bike.
Guest author: Crosbie Fitch
For a touring bike, that is expected to be heavily laden with luggage at the rear (rack mounted pack & panniers), with the additional weight of a motor and battery, one can end up with insufficient weight at the front, such that the front wheel becomes rather skittish on slippery road surfaces (gravel, sand, rain, snow, etc.). Front wheel steering and braking ends up being dangerously impaired not just due to the lack of downward weight (to improve tyre grip), but also because there is a heavily laden bike needing to be controlled or stopped. One can relocate some luggage to front panniers, but this isn’t as effective as moving a typically much heavier battery as far forward to the front as possible.
Therefore, I will now describe my approach to moving the battery to the front forks – as a pair of batteries.
Modern touring bikes often have special lugs on the front forks onto which pannier racks or fork bag brackets can be mounted. However, this is not the case on old touring bikes, such as my 1980 Claud Butler Majestic:

Being averse to an unsightly brick sized battery on a front pannier rack, I considered a pair of batteries in fork bags to be a superior solution. The compact nature of a battery (high density) would mean that a battery in each of a pair of small fork bags would appear to be less obtrusive, and make it appear as if the front wheel was not at all overly laden. There is an added bonus in that the bike would be less obviously an e-bike, and more easily assumed to be just a luggage encumbered touring bike – it would require a sharper eye to spot the motor.
To make the fork bags even less obtrusive, I sought bags of a colour that I felt would stand out the least, i.e. not red, blue, or even black. I opted for the olive-green 4 litre Rhinowalk fork bags (RK404GN). There are 6 litre bags in the same style (2cm taller & wider, 1cm deeper).
Naturally, I was careful to ensure that these could accommodate the pair of 48V 15Ah batteries I intended to purchase. As the fork bags would effectively contain the batteries, I could save a tiny bit of weight and expense by just getting plastic wrapped batteries, rather than ones encased in a hard plastic shell. It seemed that a pair of e-scooter batteries would be of the most appropriate format. Leaving a bit of bubble wrap around the batteries would provide a tad of lightweight padding in the fork bags.
Here’s my bike with batteries in the fork bags:

Given each battery is 3Kg, the bracket mounting fixings (strong cable ties - provided for forks without lugs) weren’t up to the job, and I had to use jubilee clips.
As you can see, the fork bags end up about 30 degrees from vertical, and aside from the poor aesthetics, the bags wobbled quite a bit over bumpy terrain given the linear brackets did nothing to prevent it. The wobble was likely to quickly wear the bags out (resulting in premature failure).
I evidently needed a superior mounting bracket, so this is what I cobbled together:


I found a couple of old nail plates, and drilling holes as necessary, bolted them to the forks. A ‘U’ bolt sized to fit snugly around the mid-point of the fork takes the brunt of the load, and a threaded rack/mudguard hole near the dropout enables it to be kept fixed in place. This plate then enables the placement of the fork bag’s support bracket such that it is vertical, and positioned so that each closed bag remains below the downtube (and doesn’t knock into the mudguard on sharp turns).
This resulted in a considerably superior mounting.

That looks much better, and now they don’t wobble at all (except slightly, upon braking).
Given a need to recharge the batteries after each 120-150Km or so (during long, multi-day tours), each fork bag now also contains its own battery charger (360g). To charge the batteries I now just need to open both bags up (to enable circulation of cooling air by the chargers’ fans), pull out a plug, and insert it into a mains socket. Of course, should a mains socket not be nearby, the bags can be unplugged from the motor & lighting cables (XT90 +XT30 plugs), lifted off their quick release brackets, and be carried elsewhere.
In the case of my e-bike conversion, the batteries provide power to the mid-drive CycMotor Photon, and to the lighting (twin headlights, rear rack-light, and USB smartphone charging socket).
That necessitated a one metre 8AWG XT90 extension cable from front fork bags to motor, and a 50cm low current cable from fork bags to the headset (1 male XT30 plug to 3 female XT30 sockets). The two cables are enclosed in black sheathing. Given the headlights with full/dipped beam switch were pre-wired, I stuffed its copious wiring into a little bag at the front just below the headset.
The two fork bags are linked via 3 cables (sheathed): 50cm XT90 battery cable (10AWG), 60cm low power mains cable (for 1 charger), and a 50cm switching cable (to switch charger’s 50V output).
There is a critical device that makes it possible to enable a motor to be powered by two batteries simultaneously. This seems to be called a 'dual battery discharge converter'. It automatically balances the supply of power from both batteries, irrespective of whether one battery starts off more charged than the other. They end up fully depleted together. NB Even though you end up with the combined capacity, it is not clear whether it actually increases the total current available. It could simply keep switching to the least discharged battery.
Unless you’re certain each battery’s BMS has decent short-circuit protection, I think it’s probably a good idea to insert an appropriately rated fuse on both the charging cables and the supply cables for each battery, but for the time being I’ve opted to insert just one 50A fuse - just after the discharge converter. I’ve also inserted an isolation switch at this point too (poked through a hole in the bottom of the left hand fork bag’s stiff wheel-side backing).
The schematic of the wiring is below:

I have used XT90 connectors for the high current battery/motor connections, XT60 for switching the charger outputs (for want of a non-polarised connector), and XT30 for supplying power to the lights. The batteries and chargers are supplied with 5521 connectors, so one might as well use those too to insert a switch. You could up-rate them to 5525 if the fancy takes you. For supplying mains power to the chargers, I’ve used compact IEC320 C7/C8 connectors. There are then many options for a suitable pre-made supply cable to plug into a mains socket.
I haven’t been able to find out whether chargers can be left permanently connected to batteries. Given possible leakage (slow discharge), I’ve used a DPST switch to connect/disconnect the positive wire of each charger from the respective battery’s charger input.
Here’s a photo of what the above wiring looks like when almost everything is removed from the fork bags:

All wire/wire connections are soldered and insulated with heat-shrink sleeving. Mains wire connections are additionally wrapped with insulation tape.
Connections to XT connectors are also soldered, and insulated with heat-shrink sleeving.
NB If rewiring cables from batteries, even though skin contact with 50V is not shocking, still treat it as if you are working with live mains wires. Accidentally shorting 50V is a lot worse than say 9V, and can be injurious and/or expensive.
I’ve found that all the necessary components, connectors, and cables can be obtained from online shops such as Amazon and AliExpress.
In case you’re interested in my particular set up, here are some salient details:
-
Bike: Claud Butler Majestic 1980 (frameset only)
-
Motor: CycMotor Photon gen2 + SW102T. No throttle. EU config.
-
Battery: 2x 13S3P (48V 15Ah) in Rhinowalk 4L fork bags with dual discharge converter.
-
Groupset: Box Two P9 X-Wide, single-shift, e-bike cassette.
-
Brakes: Tektro, with dual levers (drop+top).
-
Lighting: CycMotor headlights (main/off/dipped switch), Cocolumen rear rack light (6-60V), backup rechargeable headlight. Rear flasher/brake light.
-
Other: 40mm tyres. Brooks B17 saddle. Deuter rear panniers, Muvike frame lock + cable (Temu).
Here’s a front view of the bike (apologies for wheelbarrow in background):

Addendum from Electrify Bike Co.
By Adam Ostlund, Electrify Bike Co.
The dual-battery approach described above can be built with any two Electrify Bike batteries of matching voltage, one of our dual battery modules, and XT90 extension cables wherever a battery sits away from the motor. You get the combined range of both packs, and you can place the weight where your bike handles best.
What you need
-
Two Electrify Bike batteries: two 48V packs, two 52V packs, or one of each. A 48V and a 52V battery can share a module because their voltage ranges overlap from 42V to 54.6V. Two 72V packs also work as a pair with the 40–100V module.
-
A dual battery module: the Dual Battery Module 40–100V / 120A, or the Dual Battery Controller 36–72V / 80A or 24–72V / 50A. Pick one rated above your motor’s maximum current draw.
-
XT90 extension cables, as needed: anti-spark XT90 male-to-female cables in 1, 2, 3 or 4 ft lengths (30 to 120 cm), in 12AWG or 10AWG. Use 10AWG for longer runs and higher-power motors. These extensions are rated for up to 50 amps, so keep the combined draw on any extended run within that. A front-to-motor run like the 1 m cable in this build is covered by our 4 ft (120 cm) 10AWG extension.
-
A charger for each voltage you run: a 48V or 52V charger to match each battery. Two chargers let you charge both packs at once, as in this build.
How our dual battery module works
The module wires both batteries in parallel. When the two packs are at the same voltage, it combines their current as well as their capacity, up to the module’s rating. That answers the open question above: total available current does increase, not just range. If one pack starts fuller, the module draws from the higher-voltage battery until both match, then draws both down together.
Where to mount the batteries
Electrify Bike batteries come in hard, locking cases with mount cradles, so they don’t rely on a bag for protection. Common two-battery layouts are a downtube battery plus a second pack on a rear rack or second cradle; fork-mounted packs suit smaller batteries on a fork and bracket strong enough for the load, as this build shows. Check the fit of each battery with our printable battery fitment templates before you order.
Notes on the build above
-
Battery type: this build used shrink-wrapped scooter packs inside soft bags. Our hard-cased packs add impact protection, and several, including the Jumbo Shark and the triangle batteries, are UL 2271 certified.
-
Charging: charge in a well-ventilated spot with bags open or batteries removed, as the author does, and unplug the charger once charging finishes rather than leaving it connected.
-
Fusing and switching: the 50A fuse and isolation switch after the converter are sensible additions; size any fuse above your motor’s peak current.
Questions about a dual-battery build? Contact us at support@electrifybike.com.