Tongsheng TSDZ8 & TSDZ16 Owner's Guide
Electrify Bike Co. owner's guide for the Tongsheng TSDZ8 (750W) and TSDZ16 (1000W) torque-sensing mid-drive kits. These motors measure how hard you pedal and multiply your effort, for a natural ride that feels like a regular bike with superpowers.
Specifications at a Glance
| TSDZ8 | TSDZ16 | |
|---|---|---|
| Power | 750W | 1000W |
| Torque | 120+ Nm | 160 Nm |
| Battery voltage | 52V | 52V |
| Pedal assist | Torque sensor | Torque sensor + throttle |
| Display | 860C color display | 860C color display |
| Bottom bracket | 68–73mm threaded (BSA) | 68–73mm threaded (BSA) |
| Water resistance | — | IPX6 |
| Street use | Street legal at 750W | Unrestricted / off-road only |
What's in the Kit
| Item | TSDZ8 | TSDZ16 |
|---|---|---|
| Motor with built-in torque sensor | ✓ | ✓ |
| 860C color display | ✓ | ✓ |
| Throttle | — | ✓ |
| Speed sensor and magnet | ✓ | ✓ |
| Crank arms | ✓ | ✓ |
| Install wrench | ✓ | ✓ |
Before You Install: Fit Check
- Measure your bottom bracket shell width. The TSDZ8 and TSDZ16 fit 68mm or 73mm threaded (BSA) shells only.
- Press-fit, BB30 and wider fat-bike frames need an adapter or a different motor. The Bafang BBSHD or a CYC kit fits wider shells.
- Check that the motor body will clear the down tube and chainstays, and that nothing on the frame blocks it.
- Plan your battery mount. Most riders use the bottle-cage bosses or one of our battery mounts.
Installation Overview
- Remove the pedals, crank arms, front derailleur and original bottom bracket.
- Clean the bottom bracket shell, then slide the motor in from the drive side.
- Install the fixing plate and lock ring on the non-drive side and tighten them firmly with the included wrench so the motor can't rotate.
- Install the crank arms, then check your chainline and chain length.
- Mount the speed sensor on the chainstay and the magnet on a rear spoke, lined up with each other.
- Install the 860C display (and throttle on the TSDZ16), then connect them to the motor's wiring harness.
- Mount the battery, connect it to the motor and secure all cables away from the cranks and wheels.
Your kit comes set up by Electrify Bike. The TSDZ16 also has our special EBC programming for better performance at the lower assist levels. Contact us before changing motor settings.
First Ride
- Keep your feet off the pedals when you power on. The torque sensor sets its zero point at start-up, and pressure on the pedals can make assist feel weak or uneven. If that happens, power off and back on with no weight on the pedals.
- Check that the battery level reads correctly, and set the correct wheel size in the display settings.
- Start in a low assist level in an open, safe area. Torque-sensing assist responds to how hard you push, so pedal gently to start.
- Ease off the pedals for a moment while you shift to protect your chain and cassette.
Care & Maintenance
- Re-check the lock ring and crank bolts after your first 50 miles, and periodically after that.
- Clean and lube your chain often. Mid-drive motors wear chains and cassettes faster than pedaling alone.
- Keep connectors clean and dry, and check cables for wear where they bend or touch the frame.
- Store and charge your battery at room temperature, and avoid leaving it fully empty.
Quick Troubleshooting
| Problem | Check first |
|---|---|
| Display won't turn on | Battery is switched on and charged; battery cable fully connected to the motor; display connector fully seated. |
| Assist feels weak or uneven | Power off, then back on with your feet off the pedals so the torque sensor re-zeroes. |
| No assist at all | Brake levers aren't partly pressed (if brake cutoffs are fitted); speed sensor connected; wiring harness plugs fully seated. |
| Speed reads zero or assist cuts out | Speed sensor and spoke magnet are lined up and close together; sensor cable is connected. |
| Motor feels loose or clunks | Lock ring and fixing plate are tight; crank bolts are tight. |
| Error code on the display | Note the code and contact us. |
Safety
- Turn the battery off before connecting or disconnecting any cable.
- If you've fitted brake cutoffs, confirm they stop the motor before your first ride.
- Check that the motor lock ring and crank bolts are tight before each ride for the first few weeks, then periodically.
- Never pressure-wash the motor or submerge it in water.
At its full 1000W, the TSDZ16 exceeds US Class 1, 2 and 3 e-bike limits and is intended for off-road and private-land use.
Need Help?
Our team installs and programs these motors every day. Email support@electrifybike.com with your bike, motor and a photo or short video of the issue, and we'll help you sort it out.