Bafang BBS02 & BBSHD Documentation and Resources
Electrify Bike Co. documentation for the Bafang BBS02 (750W) and BBSHD (1000W) UART mid-drive kits. Every Bafang kit we sell ships with Electrify Bike optimized programming for smoother, more natural pedal assist and throttle.
EBC Manuals & Videos
- EBC BBSxx Installation Manual
- BBS02 / BBSHD Installation Video
- Gear Sensor & Brake Sensor Installation Video
- Bafang BBSHD / BBS02 Wiring Diagram
- Bafang BBSHD / BBS02 Programming Guide
Display manual
Specifications at a Glance
| BBS02 (750W) | BBSHD (1000W) | |
|---|---|---|
| Rated / peak power | 750W / ~1470W | 1000W / 1500W+ |
| Torque | 120 Nm | 160 Nm |
| Controller | 25A, UART | 30A, UART |
| Battery voltage | 48V or 52V | 48V or 52V |
| Pedal assist | Cadence sensor + throttle | Cadence sensor + throttle |
| Bottom bracket | 68–73mm threaded (BB86/92 with Lekkie adapter) | 68–73mm, 100mm or 120mm |
| Water resistance | IP65 | IP65 |
| Street use | Street legal at 750W | Unrestricted / off-road at 1000W; can be programmed to 750W |
Before You Install: Fit Check
- Measure your bottom bracket shell width. The BBS02 and standard BBSHD fit 68mm or 73mm threaded (BSA) shells. Fat bikes need the BBSHD 100mm or 120mm version.
- Press-fit frames (BB86, BB92, PF30) need an adapter to convert to a threaded shell. Contact us if you're not sure what you have.
- Check that nothing on the frame blocks the motor: the motor body sits under the down tube, and the gear housing must clear the right chainstay. Some frames need bottom bracket spacers.
- Plan your battery mount. Most riders use the bottle-cage bosses or one of our battery mounts.
Installation Overview
Follow the EBC BBSxx Installation Manual and installation video above for the full step-by-step process. In outline:
- Remove the pedals, crank arms, front derailleur and original bottom bracket.
- Clean the bottom bracket shell, then slide the motor in from the drive side.
- Install the fixing plate and the inner and outer lock rings on the non-drive side. Tighten them firmly with the Bafang bottom bracket wrench so the motor can't rotate.
- Install the chainring and crank arms, then check your chainline and chain length.
- Mount the speed sensor on the chainstay and the magnet on a rear spoke, lined up with each other.
- Install the display, throttle, brake cutoffs and (optional) gear sensor, then connect them to the motor's wiring harness.
- Mount the battery, connect it to the motor and secure all cables away from the cranks and wheels.
Your kit is already programmed by Electrify Bike. You don't need to reprogram it to ride. If you want different settings, contact us first; a bad setting can make the motor feel worse or overstress the controller and battery.
First Ride
- Power on the display and check that the battery level reads correctly.
- Set the correct wheel size in the display settings so speed and distance read accurately.
- Squeeze each brake lever and confirm the motor cuts out, before you ride anywhere.
- Start in a low assist level in an open, safe area to get used to the power.
- Ease off the pedals for a moment while you shift (or install a gear sensor) to protect your chain and cassette.
Care & Maintenance
- Re-check the lock ring and crank bolts after your first 50 miles, and periodically after that.
- Clean and lube your chain often. Mid-drive motors wear chains and cassettes faster than pedaling alone.
- Keep connectors clean and dry, and check cables for wear where they bend or touch the frame.
- Store and charge your battery at room temperature, and avoid leaving it fully empty.
Quick Troubleshooting
| Problem | Check first |
|---|---|
| Display won't turn on | Battery is switched on and charged; battery cable fully connected to the motor; display connector fully seated. |
| Display on, but no assist or throttle | Brake levers aren't partly pressed (a sticking brake cutoff stops the motor); gear sensor connected or bypassed; wiring harness plugs fully seated. |
| Speed reads zero or assist cuts out | Speed sensor and spoke magnet are lined up and close together; sensor cable is connected. |
| Motor feels loose or clunks | Lock ring and fixing plate are tight; crank bolts are tight. |
| Error code on the display | Note the code and contact us; the 860C display manual above lists what each code means. |
Safety
- Turn the battery off before connecting or disconnecting any cable.
- Always confirm the brake cutoffs stop the motor before your first ride.
- Check that the motor lock ring and crank bolts are tight before each ride for the first few weeks, then periodically.
- Never pressure-wash the motor or submerge it in water.
Need Help?
Our team installs and programs these motors every day. Email support@electrifybike.com with your bike, motor and a photo or short video of the issue, and we'll help you sort it out.